fallocate (1) - Linux Man Pages
fallocate: preallocate or deallocate space to a file
NAMEfallocate - preallocate or deallocate space to a file
SYNOPSISfallocate [-c|-p|-z] [-o offset] -l length [-n] filename
fallocate -d [-o offset] [-l length] filename
DESCRIPTIONfallocate is used to manipulate the allocated disk space for a file, either to deallocate or preallocate it. For filesystems which support the fallocate system call, preallocation is done quickly by allocating blocks and marking them as uninitialized, requiring no IO to the data blocks. This is much faster than creating a file by filling it with zeroes.
OPTIONSThe length and offset arguments may be followed by the multiplicative suffixes KiB (=1024), MiB (=1024*1024), and so on for GiB, TiB, PiB, EiB, ZiB and YiB (the "iB" is optional, e.g., "K" has the same meaning as "KiB") or the suffixes KB (=1000), MB (=1000*1000), and so on for GB, TB, PB, EB, ZB and YB.
The options --collapse-range, --dig-holes, --punch-hole and --zero-range are mutually exclusive.
- -c, --collapse-range
Removes a byte range from a file, without leaving a hole. The byte range
to be collapsed starts at offset and continues
for length bytes. At the completion of the operation, the contents of
the file starting at the location offset+length will be appended at the
location offset, and the file will be length bytes smaller. The option
--keep-size may not be specified for the collapse-range operation.
Available since Linux 3.15 for ext4 (only for extent-based files) and XFS.
- -d, --dig-holes
Detect and dig holes. This makes the file sparse in-place, without using extra
disk space. The minimum size of the hole depends on filesystem I/O block size
(usually 4096 bytes). Also, when using this option, --keep-size is
implied. If no range is specified by --offset and --length,
then the entire file is analyzed for holes.
You can think of this option as doing a "cp --sparse" and then renaming the destination file to the original, without the need for extra disk space.
See --punch-hole for a list of supported filesystems.
- -i, --insert-range
- Insert a hole of length bytes from offset, shifting existing data.
- -l, --length length
- Specifies the length of the range, in bytes.
- -n, --keep-size
- Do not modify the apparent length of the file. This may effectively allocate blocks past EOF, which can be removed with a truncate.
- -o, --offset offset
- Specifies the beginning offset of the range, in bytes.
- -p, --punch-hole
Deallocates space (i.e., creates a hole) in the byte range starting at
offset and continuing for length bytes. Within the
specified range, partial filesystem blocks are zeroed, and whole
filesystem blocks are removed from the file. After a successful
call, subsequent reads from this range will return zeroes. This option
may not be specified at the same time as the --zero-range option.
Also, when using this option, --keep-size is implied.
Supported for XFS (since Linux 2.6.38), ext4 (since Linux 3.0), Btrfs (since Linux 3.7) and tmpfs (since Linux 3.5).
- -v, --verbose
- Enable verbose mode.
- -x, --posix
- Enable POSIX operation mode. In that mode allocation operation always completes, but it may take longer time when fast allocation is not supported by the underlying filesystem.
- -z, --zero-range
Zeroes space in the byte range starting at offset and
continuing for length bytes. Within the specified range, blocks are
preallocated for the regions that span the holes in the file. After
a successful call, subsequent reads from this range will return zeroes.
Zeroing is done within the filesystem preferably by converting the range into unwritten extents. This approach means that the specified range will not be physically zeroed out on the device (except for partial blocks at the either end of the range), and I/O is (otherwise) required only to update metadata.
Option --keep-size can be specified to prevent file length modification.
Available since Linux 3.14 for ext4 (only for extent-based files) and XFS.
- -V, --version
- Display version information and exit.
- -h, --help
- Display help text and exit.
SEE ALSOtruncate(1), fallocate(2), posix_fallocate(3)
AVAILABILITYThe fallocate command is part of the util-linux package and is available from Linux Kernel Archive
Linux man pages generated by: SysTutorials