SysTutorials

Linux Manual Pages › Section 1

transmission-daemon(1)

NAME

transmission-daemon – a bittorrent client

SYNOPSIS

-words transmission-daemon –h
transmission-daemon [-a x.x.x.x,… ] [-b | B ] [-c directory ] [-C ] [-d ] [-f ] [-g directory ] [-h ] [-p port ] [-t | T ] [-u username ] [-v password ] [-P port ] [-m | M ] [-l limit ] [-L limit ] [-er | ep | et ] [-utp | no-utp ] [-V ] [-w download-dir ] [-e logfile ] [-log-error | log-info | log-debug ]

DESCRIPTION

transmission-daemon is a daemon-based Transmission session that can be controlled via RPC commands from transmission’s web interface or transmission-remote1.

OPTIONS

-a –allowed x.x.x.x,…
Allow RPC access to a comma-delimited whitelist of IP addresses. Wildcards can be specified in an address by using ‘*’. Default: "127.0.0.1" Example: "127.0.0.*,192.168.1.*"
-b –blocklist
Enable peer blocklists. Transmission understands the bluetack blocklist file format. New blocklists can be added by copying them into the config-dir’s "blocklists" subdirectory.
-c directory
Directory to watch for new .torrent files to be added. As they are added to this directory, the daemon will load them into Transmission.
-C
Do not watch for new .torrent files.
-B –no-blocklist
Disble blocklists.
-d
Dump transmission-daemon’s settings to stderr.
-f –foreground
Run in the foreground and print errors to stderr.
-g –config-dir directory
Where to look for configuration files. This can be used to swap between using the cli, daemon, gtk, and qt clients. See http://trac.transmissionbt.com/wiki/ConfigFiles for more information.
-er –encryption-required
Encrypt all peer connections.
-ep –encryption-preferred
Prefer encrypted peer connections.
-et –encryption-tolerated
Prefer unencrypted peer connections.
-gsr –global-seedratio ratio
All torrents, unless overridden by a per-torrent setting, should seed until a specific ratio
-GSR –no-global-seedratio
All torrents, unless overridden by a per-torrent setting, should seed regardless of ratio
-h –help
Print command-line option descriptions.
–incomplete-dir dir
When adding new torrents, store their contents in directory until the torrent is done.
–no-incomplete-dir
Don’t store incomplete torrents in a different directory.
-i –bind-address-ipv4
Listen for IPv4 BitTorrent connections on a specific address. Only one IPv4 listening address is allowed. Default: 0.0.0.0 (All addresses)
-I –bind-address-ipv6
Listen for IPv6 BitTorrent connections on a specific address. Only one IPv6 listening address is allowed. Default: :: (All addresses)
-r –rpc-bind-address
Listen for RPC connections on a specific address. This must be an IPv4 address. Only one RPC listening address is allowed. Default: 0.0.0.0 (All addresses)
–paused
Pause all torrents on startup
-L –peerlimit-global limit
Overall peer limit. Useful on embedded systems where the default might be unsuitable. Default: 240
-l –peerlimit-torrent limit
Peer limit per torrent. Useful on embedded systems where the default might be unsuitable. Default: 60
-m –portmap
Enable portmapping via NAT-PMP or UPnP
-M –no-portmap
Disable portmapping
-o –dht
Enable distributed hash table (DHT).
-O –no-dht
Disable distribued hash table (DHT).
-p –port port
Port to open and listen for RPC requests on. Default: 9091
-P, -peerport port
Port to listen for incoming peers on. Default: 51413
-t –auth
Require clients to authenticate themselves. This doesn’t do much good unless username and password are also set.
-T –no-auth
Don’t require authentication from clients.
-u –username username
Used for client authentication.
-v –password password
Used for client authentication.
-V –version
Show version number and exit
–utp
Enable uTP for peer connections.
–no-utp
Disable uTP for peer connections.
-w –download-dir
Where to store downloaded data.
-e –logfile
Where to store transmission’s log messages.
–log-error
Show error messages
–log-info
Show error and info messages
–log-debug
Show error, info, and debug messages

ENVIRONMENT

http_proxy
libcurl uses this environment variable when performing tracker announces.
TRANSMISSION_HOME
Sets the default config-dir.

FILES

~/.config/transmission-daemon
The config-dir used when neither [TRANSMISSION_HOME ] nor [-g ] is specified. See http://trac.transmissionbt.com/wiki/ConfigFiles for more information.

AUTHORS

An -nosplit An Jordan Lee , An Josh Elsasser , An Eric Petit , and An Mitchell Livingston .

SEE ALSO

transmission-create1, transmission-daemon1, transmission-edit1, transmission-gtk1, transmission-qt1, transmission-remote1, transmission-show1

http://www.transmissionbt.com/