exit (3) - Linux Man Pages
exit: cause normal process termination
NAMEexit - cause normal process termination
#include <stdlib.h> void exit(int status);
DESCRIPTIONThe exit() function causes normal process termination and the value of status & 0377 is returned to the parent (see wait(2)).
All functions registered with atexit(3) and on_exit(3) are called, in the reverse order of their registration. (It is possible for one of these functions to use atexit(3) or on_exit(3) to register an additional function to be executed during exit processing; the new registration is added to the front of the list of functions that remain to be called.) If one of these functions does not return (e.g., it calls _exit(2), or kills itself with a signal), then none of the remaining functions is called, and further exit processing (in particular, flushing of stdio(3) streams) is abandoned. If a function has been registered multiple times using atexit(3) or on_exit(3), then it is called as many times as it was registered.
RETURN VALUEThe exit() function does not return.
ATTRIBUTESFor an explanation of the terms used in this section, see attributes(7).
|exit()||Thread safety||MT-Unsafe race:exit|
CONFORMING TOPOSIX.1-2001, POSIX.1-2008, C89, C99, SVr4, 4.3BSD.
The behavior is undefined if one of the functions registered using atexit(3) and on_exit(3) calls either exit() or longjmp(3). Note that a call to execve(2) removes registrations created using atexit(3) and on_exit(3).
The use of EXIT_SUCCESS and EXIT_FAILURE is slightly more portable (to non-UNIX environments) than the use of 0 and some nonzero value like 1 or -1. In particular, VMS uses a different convention.
BSD has attempted to standardize exit codes; see the file <sysexits.h>.
After exit(), the exit status must be transmitted to the parent process. There are three cases:
- If the parent has set SA_NOCLDWAIT, or has set the SIGCHLD handler to SIG_IGN, the status is discarded and the child dies immediately.
- If the parent was waiting on the child, it is notified of the exit status and the child dies immediately.
- Otherwise, the child becomes a "zombie" process: most of the process resources are recycled, but a slot containing minimal information about the child process (termination status, resource usage statistics) is retained in process table. This allows the parent to subsequently use waitpid(2) (or similar) to learn the termination status of the child; at that point the zombie process slot is released.
Signals sent to other processesIf the exiting process is a session leader and its controlling terminal is the controlling terminal of the session, then each process in the foreground process group of this controlling terminal is sent a SIGHUP signal, and the terminal is disassociated from this session, allowing it to be acquired by a new controlling process.
If the exit of the process causes a process group to become orphaned, and if any member of the newly orphaned process group is stopped, then a SIGHUP signal followed by a SIGCONT signal will be sent to each process in this process group. See setpgid(2) for an explanation of orphaned process groups.
Except in the above cases, where the signalled processes may be children of the terminating process, termination of a process does not in general cause a signal to be sent to children of that process. However, a process can use the prctl(2) PR_SET_PDEATHSIG operation to arrange that it receives a signal if its parent terminates.
SEE ALSO_exit(2), get_robust_list(2), setpgid(2), wait(2), atexit(3), on_exit(3), tmpfile(3)
COLOPHONThis page is part of release 4.15 of the Linux man-pages project. A description of the project, information about reporting bugs, and the latest version of this page, can be found at https://www.kernel.org/doc/man-pages/.
Linux man pages generated by: SysTutorials