fence_cisco_mds (8) - Linux Manuals

fence_cisco_mds: Fence agent for Cisco MDS

NAME

fence_cisco_mds - Fence agent for Cisco MDS

DESCRIPTION

fence_cisco_mds is an I/O Fencing agent which can be used with any Cisco MDS 9000 series with SNMP enabled device.

fence_cisco_mds accepts options on the command line as well as from stdin. Fenced sends parameters through stdin when it execs the agent. fence_cisco_mds can be run by itself with command line options. This is useful for testing and for turning outlets on or off from scripts.

Vendor URL: http://www.cisco.com

PARAMETERS

        

-u, --ipport=[port]
TCP/UDP port to use for connection with device (Default Value: 161)         
-d, --snmp-version=[version]
Specifies SNMP version to use (1,2c,3)         
-c, --community=[community]
Set the community string         
-B, --snmp-priv-prot=[prot]
Set privacy protocol (DES|AES)         
-n, --plug=[id]
Physical plug number, name of virtual machine or UUID This parameter is always required.         
-6, --inet6-only
Forces agent to use IPv6 addresses only         
-a, --ip=[ip]
IP Address or Hostname This parameter is always required.         
-P, --snmp-priv-passwd=[pass]
Set privacy protocol password         
-R, --snmp-priv-passwd-script
Script to run to retrieve privacy password         
-b, --snmp-auth-prot=[prot]
Set authentication protocol (MD5|SHA)         
-4, --inet4-only
Forces agent to use IPv4 addresses only         
-S, --password-script=[script]
Script to retrieve password         
-E, --snmp-sec-level=[level]
Set security level (noAuthNoPriv|authNoPriv|authPriv)         
-p, --password=[password]
Login password or passphrase         
-o, --action=[action]
Fencing Action (Default Value: off)         
-l, --username=[name]
Login Name         
-v, --verbose
Verbose mode         
-D, --debug-file=[debugfile]
Write debug information to given file         
-V, --version
Display version information and exit         
-h, --help
Display help and exit         
-C, --separator=[char]
Separator for CSV created by operation list (Default Value: ,)         
--power-wait=[seconds]
Wait X seconds after issuing ON/OFF (Default Value: 0)         
--login-timeout=[seconds]
Wait X seconds for cmd prompt after login (Default Value: 5)         
--power-timeout=[seconds]
Test X seconds for status change after ON/OFF (Default Value: 20)         
--delay=[seconds]
Wait X seconds before fencing is started (Default Value: 0)         
--shell-timeout=[seconds]
Wait X seconds for cmd prompt after issuing command (Default Value: 3)         
--retry-on=[attempts]
Count of attempts to retry power on (Default Value: 1)

ACTIONS

        

on
Power on machine.         
off
Power off machine.         
status
This returns the status of the plug/virtual machine.         
list
List available plugs with aliases/virtual machines if there is support for more then one device. Returns N/A otherwise.         
list-status
List available plugs with aliases/virtual machines and their power state if it can be obtained without additional commands.         
monitor
Check the health of fence device         
metadata
Display the XML metadata describing this resource.

STDIN PARAMETERS

        

ipport
TCP/UDP port to use for connection with device (Default Value: 161)         
snmp_version
Specifies SNMP version to use (1,2c,3)         
community
Set the community string         
snmp_priv_prot
Set privacy protocol (DES|AES)         
port
Physical plug number, name of virtual machine or UUID This parameter is always required.         
inet6_only
Forces agent to use IPv6 addresses only         
ipaddr
IP Address or Hostname This parameter is always required.         
snmp_priv_passwd
Set privacy protocol password         
snmp_priv_passwd_script
Script to run to retrieve privacy password         
snmp_auth_prot
Set authentication protocol (MD5|SHA)         
inet4_only
Forces agent to use IPv4 addresses only         
passwd_script
Script to retrieve password         
snmp_sec_level
Set security level (noAuthNoPriv|authNoPriv|authPriv)         
passwd
Login password or passphrase         
action
Fencing Action (Default Value: off)         
login
Login Name         
verbose
Verbose mode         
debug
Write debug information to given file         
version
Display version information and exit         
help
Display help and exit         
separator
Separator for CSV created by operation list (Default Value: ,)         
power_wait
Wait X seconds after issuing ON/OFF (Default Value: 0)         
login_timeout
Wait X seconds for cmd prompt after login (Default Value: 5)         
power_timeout
Test X seconds for status change after ON/OFF (Default Value: 20)         
delay
Wait X seconds before fencing is started (Default Value: 0)         
shell_timeout
Wait X seconds for cmd prompt after issuing command (Default Value: 3)         
retry_on
Count of attempts to retry power on (Default Value: 1)