mrtg-reference – MRTG 2.17.4 configuration reference OverviewThe runtime behaviour of MRTG is governed by a configuration file. Run-of-the-mill configuration files can be generated with cfgmaker. (Check cfgmaker). But for more elaborate configurations some hand-tuning is required. This document describes all the configuration options understood by the mrtg software. SyntaxMRTG configuration file syntax follows some simple…
mrtg-nw-guide – MRTG for NetWare SynopsisThis guide is intended to aid in the installation and configuration of MRTG on a NetWare server. OverviewMRTG is a relative newcomer to the NetWare platform. Earlier versions of NetWare could not run MRTG natively for several reasons: • Absence of NetWare OS support in the MRTG package. • A…
mrtg-nt-guide – The MRTG 2.17.4 Windows Installation Guide SynopsisInstalling MRTG on a Windows box is not quite as “click and point” as some might want it to be. But then again, it is not all that difficult if you follow the instructions below. PrerequisitesTo get MRTG to work on Windows you need the following: •…
mrtg-mibhelp – A Table of some interesting OIDs OverviewThis File Contains a collection of interesting MIB Entries … mrtg knows about their names … depending on the ASN.1 Syntax you may have to put gauge into the Options[]: parameter. For information about how to create a Target[]: parameter which references these MIB entries, please consult…
mrtg-logfile – description of the mrtg-2 logfile format SynopsisThis document provides a description of the contents of the mrtg-2 logfile. OverviewThe logfile consists of two main sections. The first Line It stores the traffic counters from the most recent run of mrtg. The rest of the File Stores past traffic rate averates and maxima at…
mrtg-ipv6 – IPv6 support in MRTG OverviewMRTG and cfgmaker support SNMP over IPv6. IPv6 targets can be specified by hostname or IPv6 address, and if the required libraries are present (see below), queries will use IPv6. UsageEnabling IPv6IPv6 is currently disabled by default and must be explicitly enabled. In MRTG this is done by turning…
mrtg-forum – Interactive Help for MRTG users SynopsisThere is a lot of written documentation for mrtg, but nevertheless you may have a problem where you can’t find the solution. In this case some Human Help may be necessary. With MRTG there are several ways to get Humans to help you. Mailing-ListThere are three mailing lists…
mrtg-faq – How to get help if you have problems with MRTG SynopsisMRTG seems to raise a lot of questions. There are a number of resources apart from the documentation where you can find help for mrtg. FaqIn the following sections you’ll find some additonal Frequently Asked Questions, with Answers. Why is there no @#$%…
mrtg-contrib – Contribution Guidelines for MRTG DescriptionIf you have written an extension to mrtg or created a bug fix, please consider contributing it to the project. As I get quite a number of contributions every week, here are a few guidelines which explain how to contribute so that I can use the contribution without too…
mrpt-performance – Complete performance test for MRPT Synopsismrpt-performance Descriptionmrpt-performance is a command-line tool for performing a complete test of performance (in execution time) of many different modules of MRPT. The results are dumped as an HTML document. BugsPlease report bugs at http://sourceforge.net/tracker/?group_id=205280&atid=993006 See AlsoThe application wiki page at http://babel.isa.uma.es/mrpt/index.php/Applications Authorsmrpt-performance is part of the Mobile…
mrftopbm – convert an MRF image to PBM format Synopsismrftopbm [ -a ] [ input.mrf ] DescriptionThis program is part of Netpbm(1) mrftopbm converts an MRF image to PBM format. mrftopbm takes the MRF image from the file named by the input.mrf argument, or Standard Input if you don’t specify input.mrf. The output goes to…
MRF – monochrome recursive format (compressed bitmaps) DescriptionThis program is part of Netpbm(1) MRF is a compressed format for bilevel (1-bit mono) images. It achieves better compression for some such images than either GIF or PNG. (It’s also very easy to implement (about the same difficulty as RLE, I’d say) and an MRF reader needs…
mren – rename an existing MSDOS file Note of warningThis manpage has been automatically generated from mtools’s texinfo documentation, and may not be entirely accurate or complete. See the end of this man page for details. DescriptionThe mren command is used to rename or move an existing MS-DOS file or subdirectory. Its syntax is: mren…
mrd – remove an MSDOS subdirectory Note of warningThis manpage has been automatically generated from mtools’s texinfo documentation, and may not be entirely accurate or complete. See the end of this man page for details. DescriptionThe mrd command is used to remove an MS-DOS subdirectory. Its syntax is: mrd [-v] msdosdirectory [ msdosdirectories… ] Mrd…
rancid – Cisco configuration filter Synopsisrancid [-dlCV] [-t device_type] (-f filename | hostname) rancid [-dhlCV] -t device_type (-f filename | hostname) Descriptionrancid is a collection of perl(1) scripts which uses the login scripts (see clogin(1)) to login to a device, execute commands to display the configuration, etc, then filters the output for formatting, security, and…
mr – a tool to manage all your version control repos Synopsismr [options] checkout mr [options] update mr [options] status mr [options] clean [-f] mr [options] commit [-m “message”] mr [options] record [-m “message”] mr [options] fetch mr [options] push mr [options] diff mr [options] log mr [options] grep pattern mr [options] run command [param…
mpv – a media player Synopsismpv [options] [file|URL|PLAYLIST|-] mpv [options] filesDescriptionmpv is a media player based on MPlayer and mplayer2. It supports a wide variety of video file formats, audio and video codecs, and subtitle types. Special input URL types are available to read input from a variety of sources other than disk files. Depending…
mptopdf – convert MetaPost figures to PDF Synopsismptopdf [ OPTIONS … ] [ FILENAMES ] Descriptionconvert MetaPost figures to PDF Options–metafun use the metafun format to process the file (default is mpost) –texexec use texexec (context) to process text snippets –latex use latex to process text snippetsAuthorMore information about ConTeXt and the tools that come…
mpto – extract labels in MetaPost pictures for typesetting Synopsismpto [-tex|-troff] mpfile DescriptionThis manual page is not meant to be exhaustive. The complete documentation for this version of TeX can be found in the info file or manual Web2C: A TeX implementation. Strip btex..etex and verbatimtex…etex parts from MetaPost input file mpfile, converting to either…
mpstat – Report processors related statistics. Synopsismpstat [ -A ] [ –dec={ 0 | 1 | 2 } ] [ -n ] [ -u ] [ -T ] [ -V ] [ -I { keyword[,…] | ALL } ] [ -N { node_list | ALL } ] [ -o JSON ] [ -P { cpu_list…