pmconfig – Performance Co-Pilot configuration parameters Synopsis$PCP_BINADM_DIR/pmconfig [-a|-l] [-L] [-s] [name …] Descriptionpmconfig displays the values for some or all configuration parameters of the local Performance Co-Pilot toolkit installation. The -L option may be used to change the default reporting mode so that the capabilities of the PCP library are reported, rather than the PCP…
pmclient, pmclient_fg – a simple performance metrics client Synopsispmclient [-a archive] [-h host] [-n pmnsfile] [-P] [-S numsec] [-s samples] [-t interval] [-Z timezone] [-z] Descriptionpmclient and pmclient_fg are simple clients that use the Performance Metrics Application Programming Interface (PMAPI) to report some high-level system performance metrics. The real value of these tools is as…
pmcheck – check that Perl is set up correctly for Perl modules Descriptionpmcheck checks that Perl is correctly set up for Perl modules. For now, pmcheck just verifies that the entries in @INC are existing readable directories. See Alsopmdirs(1), pmpath(1) AUTHOR and COPYRIGHTSCopyright (C) 2012-2014 Mark Leighton Fisher. LicenseThis is free software; you can redistribute…
pmchart – strip chart tool for Performance Co-Pilot Synopsispmchart [-CVWz] [-A align] [-a archive] [-c configfile] [-f fontfamily] [-F fontsize] [-g geometry] [-h host] [-o outfile] [-O offset] [-p port] [-s samples] [-S starttime] [-T endtime] [-t interval] [-v visible] [-Z timezone] [-geometry geometry] [sources…] Descriptionpmchart is a graphical utility that plots performance metrics values…
pmcd_wait – wait for PMCD to accept client connections Synopsis$PCP_BINADM_DIR/pmcd_wait [-h host] [-t interval] [-v] Descriptionpmcd_wait waits for the Performance Metrics Collector Daemon (PMCD) to be running and accepting client connections. Unless directed to another host by the -h option, pmcd_wait will try to contact pmcd(1) on the local host. pmcd_wait will timeout and abandon…
pmcd – performance metrics collector daemon Synopsispmcd [-AfQSv] [-c config] [-C dirname] [-H hostname] [-i ipaddress] [-l logfile] [-L bytes] [-M certname] [–[n|N] pmnsfile] [-p port[,port …]] [-P passfile] [-q timeout] [-s sockname] [-T traceflag] [-t timeout] [-U username] [-x file] Descriptionpmcd is the collector used by the Performance Co-Pilot (see PCPIntro(1)) to gather performance…
pmcat – page through a module file DescriptionGiven a module name, figure out the path name and send that to the user’s pager. $ pmcat CGIThis works also on alternate installed versions of Perl: $ oldperl -S pmcat strict $ filsperl -S pmcat ThreadsThis command is mostly here for people too lazy to type $…
pmap – report memory map of a process Synopsispmap [options] pid […] DescriptionThe pmap command reports the memory map of a process or processes. Options-x, –extended Show the extended format. -d, –device Show the device format. -q, –quiet Do not display some header or footer lines. -A, –range low,high Limit results to the given range…
pman – show a module’s man page DescriptionSend a module’s pod through pod2text and your pager. This is mostly here for people too lazy to type $ pod2text `pmpath CGI` | $PAGERExamples $ pman CGI $ pman CursesOr running under different versions of Perl: $ oldperl -S pman CGI $ filsperl -S pman ThreadsSee Alsopod2text(1),…
pmall – show all installed versions and descs Synopsis pmall [-d] [-w] [-a] [-s]pmall – show all installed versions and descs DescriptionThis program runs through all your installed modules and tells you what they’re for and what version number they are at. The following options are honored: -v give debug info -w warn about missing…
pmafm – Performance Co-Pilot archive folio manager Synopsispmafm folioname [command [arg …]] DescriptionA collection of one or more Performance Co-Pilot (PCP) archive logs may be combined with a control file to produce a PCP archive folio. Archive folios are created using either mkaf(1) or the interactive “record mode” services of PCP clients like pmchart(1). pmafm…
pm_which – find installed modules Synopsis pm_which [ options ] module(s) Returns the path to the given module(s)OPTIONS -q, –quiet Just print paths -p, –paths Just convert the module name into a relative path -a, –all Print all paths, not just the first one found -n, –namespace Print all modules in the given namespace -m…
pm-is-supported – Test whether suspend or hibernate is supported. Synopsis pm-is-supported [{–suspend | –hibernate | –suspend-hybrid}]DescriptionThis manual page documents briefly the pm-is-supported command. The intended purpose of pm-is-supported is to find out which power management modes are supported by the system. hald(8) will call it to do just that. (Note that UPower does not use this.) Options–suspend Test whether…
plymouth – Send commands to plymouthd Synopsis plymouth [OPTION…] plymouth COMMAND [OPTION…] DescriptionThe plymouth sends commands to a running plymouthd. This is used during the boot process to control the display of the graphical boot splash. OptionsThe following options are understood. These options are supported for compatibility with the old rhgb-client interface, and have been replaced…
plymouth-set-default-theme – Set the plymouth theme Synopsis plymouth-set-default-theme [OPTION…][THEME]DescriptionWhen called with a THEME argument, the plymouth-set-default-theme command changes the preferred boot theme and also performs the necessary regeneration of the initial ramdisk (initrd) since plymouth is loaded from the boot loader from the initrd prior to the mounting of the root filesystem. If plymouth-set-default-theme is…
plxload – show what files a perl program loads at compile time Synopsys $ plxloadDescriptionThis program is used to show what modules a program would load at compile time via "use". Because this installs an at-exit handler and then uses Perl’s -c flag for compile only, it will not find modules loaded at run-time. Use…
Pluma – The MATE Text Editor Synopsispluma [OPTIONS…] [FILES…] DescriptionPluma is the official text editor of the MATE desktop environment. While aiming at simplicity and ease of use, Pluma is a powerful general purpose text editor. It can be used to create and edit all sorts of text files. Pluma features a flexible plugin system…
plugreport – a program to read all MPR/PCR registers from all devices and report them. Synopsis plugreport DescriptionThis manual page documents briefly the plugreport and was written for the Debian distribution because the original program does not have a manual page. plugreport is a program to read all MPR/PCR registers from all devices and report…
plugctl – a program to get or set any MPR or PCR register value Synopsis plugctl [-p port] [-n node] plug.attribute[=value] Descriptionplugctl is a program to get or set the value of a plug’s attribute. plug is one of oMPR, iMPR, oPCR[n], or iPCR[n] (case insensitive). Please supply a numerical index for [n]. This manual page was…
pltotf – convert property list files to TeX font metric (tfm) format Synopsispltotf [-verbose] pl_file_name[.pl] [tfm_file_name[.tfm]] DescriptionThis manual page is not meant to be exhaustive. The complete documentation for this version of TeX can be found in the info file or manual Web2C: A TeX implementation. The pltotf program translates a (human-oriented) property list file…