taskrc – Configuration details for the task(1) command Synopsis $HOME/.taskrc task rc:<directory-path>/.taskrc … TASKRC=<directory-path>/.taskrc task … Description Taskwarrior obtains its configuration data from a file called .taskrc . This file is normally located in the user’s home directory: $HOME/.taskrc The default location can be overridden using the rc: attribute when running task: $ task rc:<directory-path>/.taskrc…
task-sync – A discussion and tutorial for the various task(1) data synchronization capabilities. Introduction Taskwarrior has several sync options, external and internal. If you wish to sync your data, choose one method only; mixing methods is only going to lead to problems. Each of the methods discussed have their own strengths. Alternatives There are three…
task-color – A color tutorial for the Taskwarrior command line todo manager. Setup The first thing you need is a terminal program that supports color. All terminal programs support color, but only a few support lots of colors. First tell your terminal program to use color by specifying the TERM environment variable like this: TERM=xterm-color…
tarsnap.conf – configuration file for tarsnap(1) Description The file is read by the tarsnap(1) utility and specifies default options which will be ignored if the options in question are specified at the command line. Options may be specified in /etc/tarsnap.conf and/or ~/.tarsnaprc if the two files conflict, the user’s local configuration takes precedence. The file(s)…
targets – configuration file for iSCSI targets Synopsis targets Description The targets file describes the iSCSI storage which is presented to iSCSI initiators by the iscsi-target8 service. A description of the iSCSI protocol can be found in "Internet Small Computer Systems Interface \*(tNRFC\*(sP 3720" . Each line in the file (other than comment lines that…
tar – format of tape archive files Description The archive format collects any number of files, directories, and other file system objects (symbolic links, device nodes, etc.) into a single stream of bytes. The format was originally designed to be used with tape drives that operate with fixed-size blocks, but is widely used as a…
tapelist – The list of Amanda volumes in use Description The tapelist file contains the list of tapes in active use. This file is not ordinarily ordinarily edited or examined manually. Its format may change, or it may be removed altogether, in future versions of Amanda. It contains lines of the form: YYYYMMDD label flags…
table – format description for smtpd tables Description This manual page documents the file format for the various tables used in the smtpd(8) mail daemon. The format described here applies to tables as defined in smtpd.conf(5). Table Types There are two types of tables: lists and mappings. A list consists of a series of values,…
sysusers.d – Declarative allocation of system users and groups Synopsis /usr/lib/sysusers.d/*.conf Description systemd-sysusers uses the files from sysusers.d directory to create system users and groups at package installation or boot time. This tool may be used to allocate system users and groups only, it is not useful for creating non-system users and groups, as it…
sysusers.d – Declarative allocation of system users and groups Synopsis /etc/sysusers.d/*.conf /run/sysusers.d/*.conf /usr/lib/sysusers.d/*.conf #Type Name ID GECOS Home directory Shell u user_name uid "User Description" /home/dir /path/to/shell u user_name uid:gid "User Description" /home/dir /path/to/shell u user_name /file/owned/by/user "User Description" /home/dir /path/to/shell g group_name gid g group_name /file/owned/by/group m user_name group_name r – lowest-highest Description systemd-sysusers…
systemd.unit – Unit configuration Synopsis service.service, socket.socket, device.device, mount.mount, automount.automount, swap.swap, target.target, path.path, timer.timer, slice.slice, scope.scope System Unit Search Path /etc/systemd/system.control/* /run/systemd/system.control/* /run/systemd/transient/* /run/systemd/generator.early/* /etc/systemd/system/* /etc/systemd/system.attached/* /run/systemd/system/* /run/systemd/system.attached/* /run/systemd/generator/* … /lib/systemd/system/* /run/systemd/generator.late/* User Unit Search Path ~/.config/systemd/user.control/* $XDG_RUNTIME_DIR/systemd/user.control/* $XDG_RUNTIME_DIR/systemd/transient/* $XDG_RUNTIME_DIR/systemd/generator.early/* ~/.config/systemd/user/* $XDG_CONFIG_DIRS/systemd/user/* /etc/systemd/user/* $XDG_RUNTIME_DIR/systemd/user/* /run/systemd/user/* $XDG_RUNTIME_DIR/systemd/generator/* $XDG_DATA_HOME/systemd/user/* $XDG_DATA_DIRS/systemd/user/* … /usr/lib/systemd/user/* $XDG_RUNTIME_DIR/systemd/generator.late/* Description A unit file…
systemd.timer – Timer unit configuration Synopsis timer.timer Description A unit configuration file whose name ends in ".timer" encodes information about a timer controlled and supervised by systemd, for timer-based activation. This man page lists the configuration options specific to this unit type. See systemd.unit(5) for the common options of all unit configuration files. The common…
systemd.target – Target unit configuration Synopsis target.target Description A unit configuration file whose name ends in ".target" encodes information about a target unit of systemd, which is used for grouping units and as well-known synchronization points during start-up. This unit type has no specific options. See systemd.unit(5) for the common options of all unit configuration…
systemd.swap – Swap unit configuration Synopsis swap.swap Description A unit configuration file whose name ends in ".swap" encodes information about a swap device or file for memory paging controlled and supervised by systemd. This man page lists the configuration options specific to this unit type. See systemd.unit(5) for the common options of all unit configuration…
systemd.socket – Socket unit configuration Synopsis socket.socket Description A unit configuration file whose name ends in ".socket" encodes information about an IPC or network socket or a file system FIFO controlled and supervised by systemd, for socket-based activation. This man page lists the configuration options specific to this unit type. See systemd.unit(5) for the common…
systemd.snapshot – Snapshot unit configuration Synopsis snapshot.snapshot Description Snapshot units are not configured via unit configuration files. Nonetheless they are named similar to filenames. A unit whose name ends in ".snapshot" refers to a dynamic snapshot of the systemd runtime state. Snapshots are not configured on disk but created dynamically via systemctl snapshot (see systemctl(1)…
systemd.slice – Slice unit configuration Synopsis slice.slice Description A unit configuration file whose name ends in ".slice" encodes information about a slice unit. A slice unit is a concept for hierarchically managing resources of a group of processes. This management is performed by creating a node in the Linux Control Group (cgroup) tree. Units that…
systemd.service – Service unit configuration Synopsis service.service Description A unit configuration file whose name ends in ".service" encodes information about a process controlled and supervised by systemd. This man page lists the configuration options specific to this unit type. See systemd.unit(5) for the common options of all unit configuration files. The common configuration items are…
systemd.scope – Scope unit configuration Synopsis scope.scope Description Scope units are not configured via unit configuration files, but are only created programmatically using the bus interfaces of systemd. They are named similar to filenames. A unit whose name ends in ".scope" refers to a scope unit. Scopes units manage a set of system processes. Unlike…
systemd.resource-control – Resource control unit settings Synopsis slice.slice, scope.scope, service.service, socket.socket, mount.mount, swap.swap Description Unit configuration files for services, slices, scopes, sockets, mount points, and swap devices share a subset of configuration options for resource control of spawned processes. Internally, this relies on the Linux Control Groups (cgroups) kernel concept for organizing processes in a…