Section 5: file formats
ipmi_monitoring_sensors.conf – specify sensor interpretation rules Description The /etc/ipmi_monitoring_sensors.conf defines how IPMI sensors should be interpreted. IPMI based sensors specify a number of states/thresholds when they are read. Based on those states/thresholds we can allow the libipmimonitoring(3) library and ipmimonitoring(8) tool to report if a sensor reading is "good" or "bad" (or in a NOMINAL,…
freeipmi_interpret_sensor.conf – specify sensor interpretation rules Description The /etc/freeipmi//freeipmi_interpret_sensor.conf defines how IPMI sensors should be interpreted. IPMI based sensors specify a number of states/thresholds when they are read. Based on those states/thresholds, libraries and tools such as libfreeipmi(3), libipmimonitoring(3) and ipmi-sensors(8) can report if a sensor reading is "good" or "bad" via a report of…
ipmidetectd.conf – ipmidetectd configuration file Description The ipmidetectd configuration file configures the ipmidetectd daemon. The default configuration file loaded is /etc/ipmidetectd.conf. The configuration options that can be specified in the configuration file are listed below. Each configuration option must be listed on a separate line. Arguments for an option are separated by any amount of…
ipmidetectd.conf – ipmidetectd configuration file Description The ipmidetectd configuration file configures the ipmidetectd daemon. The default configuration file loaded is /etc/freeipmi//ipmidetectd.conf. The configuration options that can be specified in the configuration file are listed below. Each configuration option must be listed on a separate line. Arguments for an option are separated by any amount of…
ipmidetect.conf – specify alternate default values for the ipmidetect library Description Through a configuration file, system administrators may override the default values used in the ipmidetect_load_data(3) API function. The configuration file is stored at /etc/ipmidetect.conf. Configuration Options The following are a list of configuration options that can be specified in the configuration file. Each configuration…
ipmidetect.conf – specify alternate default values for the ipmidetect library Description Through a configuration file, system administrators may override the default values used in the ipmidetect_load_data(3) API function. The configuration file is stored at /etc/freeipmi//ipmidetect.conf. Configuration Options The following are a list of configuration options that can be specified in the configuration file. Each configuration…
freeipmi.conf – specify default values to FreeIPMI Description The FreeIPMI configuration file can be used to set alternate default values to many FreeIPMI tools so values don’t have to be configured on the command line. This allows users to avoid typing in a long list of command line options everytime a command is executed. It…
ipmi_monitoring_sensors.conf – specify sensor interpretation rules Description The /etc/ipmi_monitoring_sensors.conf defines how IPMI sensors should be interpreted. IPMI based sensors specify a number of states/thresholds when they are read. Based on those states/thresholds we can allow the libipmimonitoring(3) library and ipmimonitoring(8) tool to report if a sensor reading is "good" or "bad" (or in a NOMINAL,…
freeipmi_interpret_sensor.conf – specify sensor interpretation rules Description The /etc/freeipmi//freeipmi_interpret_sensor.conf defines how IPMI sensors should be interpreted. IPMI based sensors specify a number of states/thresholds when they are read. Based on those states/thresholds, libraries and tools such as libfreeipmi(3), libipmimonitoring(3) and ipmi-sensors(8) can report if a sensor reading is "good" or "bad" via a report of…
svipc – System V interprocess communication mechanisms Synopsis #include <sys/msg.h> #include <sys/sem.h> #include <sys/shm.h> Description This manual page refers to the Linux implementation of the System V interprocess communication (IPC) mechanisms: message queues, semaphore sets, and shared memory segments. In the following, the word resource means an instantiation of one among such mechanisms. Resource access…
intuitively.conf – Configuration file for intuitively Synopsis intuitively.conf controls how intuitively behaves. Example Intuitively.Conf [work] myip = 192.168.1.253 netmask = 255.255.255.0 other_ip = 192.168.1.1 #router other_ip = 192.168.1.2 = aa:bb:cc:dd:ee:ff #general server w/ethernet address default_gw = 192.168.1.1 description = Work #script = /usr/share/intuitively/work.sh [home] myip = 192.168.199.6 netmask = 255.255.255.0 other_ip = 192.168.199.2 other_ip =…
intro – introduction to file formats and filesystems Description Section 5 of the manual describes various file formats, as well as the corresponding C structures, if any. In addition, this section contains a number of pages that document various filesystems. Notes Authors and copyright conditions Look at the header of the manual page source for…
/etc/network/interfaces – network interface configuration for ifup and ifdown Description /etc/network/interfaces contains network interface configuration information for the ifup(8) and ifdown(8) commands. This is where you configure how your system is connected to the network. Example The following example configures two network interfaces: eth0 is brought up at boot, and uses DHCP for IPv4 and…
interface-order – resolvconf configuration file Description The file /etc/resolvconf/interface-order is used to control the order in which resolvconf nameserver information records are processed by those resolvconf update scripts that consult this file. (The name of the file is apt because a resolvconf nameserver information record is named after the interface with which it is associated.)…
innwatch.ctl – control Usenet supervision by innwatch Description The file <pathetc in inn.conf>/innwatch.ctl is used to determine what actions are taken during the periodic supervisions by innwatch. The file consists of a series of lines; blank lines and lines beginning with a number sign (“#”) are ignored. All other lines consist of seven fields, each…
innwatch.ctl – control Usenet supervision by innwatch Description The file <pathetc in inn.conf>/innwatch.ctl is used to determine what actions are taken during the periodic supervisions by innwatch. The file consists of a series of lines; blank lines and lines beginning with a number sign (“#”) are ignored. All other lines consist of seven fields, each…
innfeed.conf – configuration file for innfeed Description This man page describes the configuration file for version 1.0 of innfeed. This format has changed dramatically since version 0.9.3. The file innfeed.conf is used to control the innfeed(1) program. It is a fairly free-format file that consists of three types of entries: key/value, peer and group. Comments…
innfeed.conf – Configuration file for innfeed Description The configuration file innfeed.conf in pathetc is used to control the innfeed(8) program. It is a fairly free-format file that consists of three types of entries: key:value, peer and group. Comments are from the hash character "#" to the end of the line. key:value entries are a keyword…
inn.conf – Configuration data for InterNetNews programs Description inn.conf in pathetc is the primary general configuration file for all InterNetNews programs. Settings which control the general operation of various programs, as well as the paths to all portions of the news installation, are found here. The INNCONF environment variable, if set, specifies an alternate path…
inn.conf – Configuration data for InterNetNews programs Description inn.conf in pathetc is the primary general configuration file for all InterNetNews programs. Settings which control the general operation of various programs, as well as the paths to all portions of the news installation, are found here. The INNCONF environment variable, if set, specifies an alternate path…