Section 8: administration and privileged commands
atmtcp – set up ATM over TCP connections Synopsis atmtcp [-d] [-v] command … atmtcp -V Description The main purpose of atmtcp is to establish TCP connections and to configure them as virtual ATM devices. Such pairs of "ATM over TCP" devices are connected as if they were real ATM adapters linked by a cable…
atmsigd – ATM signaling demon Synopsis atmsigd [-b] [-c config_file] [-d] [-D dump_dir] [-l logfile] [-m mode] [-n] [-q qos] [-t trace_length] [-u uni_version] [[itf.]vpi.vci [input output]] atmsigd -V Description atmsigd implements the ATM UNI signaling protocol. Requests to establish, accept, or close ATM SVCs are sent from the kernel (using a comparably simple protocol) to the signaling demon, which then performs…
atmloop – get/set loopback mode of ATM interfaces Synopsis atmloop -s [-l level] [-r level] [itf] atmloop [itf] atmloop -q [itf] atmloop -V Description atmloop sets or shows the current loopback settings of an ATM interface, and allows to query the loopback modes supported by the interface. Some ATM cards can be configured to echo data back…
atmdump – capture or generate ATM cells Synopsis atmdump [-i] [ -t type [-g gfc] [-c] ] [itf.]vpi.vci Description atmdump captures or generates single ATM cells ("AAL0"). When capturing cells, a time stamp, the cell header contents, and a hex dump of the cell payload are shown. When sending cells, the payload type, the generic flow control…
atmdiag – show ATM device driver diagnostics Synopsis atmdiag [-z] [interface…] Description atmdiag shows statistic counters maintained by ATM device drivers. If one or more interface numbers are specified, the statistics of only these interfaces are shown. Otherwise, statistics of all interfaces are displayed. The following counters are shown for each AAL: TX_okay number of…
atmarpd – ATMARP demon Synopsis atmarpd [-b] [-d] [-D directory] [-l logfile] [-m] [-n] atmarpd -V Description atmarpd implements the ATMARP protocol as specified in RFC1577 and RFC1755. Address resolution requests are sent from the kernel (using a comparably simple protocol) to the ATMARP demon, which then performs the dialog with the network. atmarpd can operate as…
atmarp – administer classical IP over ATM connections Synopsis atmarp -a atmarp -c [[atm]number] atmarp -q ip_addr [qos qos] [sndbuf bytes] atmarp -s ip_addr [itf.]vpi.vci [qos qos] [sndbuf bytes] [temp] [pub] [null] atmarp -s ip_addr atm_addr [qos qos] [sndbuf bytes] [temp] [pub] [arpsrv] atmarp -d ip_addr [arpsrv] atmarp -V Description atmarp is used to maintain the ATMARP table of the ATMARP…
atmaddr – list and maintain local ATM addresses Synopsis atmaddr [-n] [itf] atmaddr -r [itf] atmaddr -a [itf] atm_addr atmaddr -d [itf] atm_addr atmaddr -V Description atmaddr is used to list the local addresses configured for ATM interfaces and to manually change the list of addresses. If the interface number itf is omitted, interface 0 is used by…
ath_info – print module version info, write some eeprom fields Synopsis ath_info [-w [-g N:M]] [-v] [-f] <pci_address> [<field1> <val1> [<field2> <val2> …]] Description ath_info prints some version information of Atheros WLAN modules. It furthermore allows to change regulatory domain and PCI ID fields in the EEPROM. You must first retrieve the PCI memory address…
atd – run jobs queued for later execution Synopsis atd [-l load_avg] [-b batch_interval] [-d] [-f] [-s] Description atd runs jobs queued by at(1). Options -l Specifies a limiting load factor, over which batch jobs should not be run, instead of the compile-time choice of 0.8. For an SMP system with n CPUs, you will…
atalkd – AppleTalk RTMP, NBP, ZIP, and AEP manager Synopsis atalkd [-f configfile] [-1] [-2] Description atalkd is responsible for all user level AppleTalk network management. This includes routing, name registration and lookup, zone lookup, and the AppleTalk Echo Protocol (similar to ping(8)). atalkd is typically started at boot time, out of /etc/rc. It first reads…
astraceroute – autonomous system trace route utility Synopsis astraceroute [options] Description astraceroute is a small utility to retrieve path information in a traceroute like way, but with additional geographical location information. It tracks the route of a packet from the local host to the remote host by successively increasing the IP’s TTL field, starting from…
astgenkey — generates keys for for Asterisk IAX2 RSA authentication Synopsis astgenkey [ -q ] [ -n ] [ keyname ] Description astgenkey This script generates an RSA private and public key pair in PEM format for use by Asterisk. The private key should be kept a secret, as it can be used to fake…
asterisk_selinux – Security Enhanced Linux Policy for the asterisk processes Description Security-Enhanced Linux secures the asterisk processes via flexible mandatory access control. The asterisk processes execute with the asterisk_t SELinux type. You can check if you have these processes running by executing the ps command with the -Z qualifier. For example: ps -eZ | grep…
asterisk – All-purpose telephony server. Synopsis asterisk [ -tThfdvVqpRgciIn ] [ -C file ] [ -U user ] [ -G group ] [ -x command ] [ -M value ] asterisk -r [ -v ] [ -x command ] [ -s socket ] Description asterisk is a full-featured telephony server which provides Private Branch eXchange…
aspell-autobuildhash – Autobuilding aspell hash files for some dicts Synopsis aspell-autobuildhash [–force] Options: –debug Show extra info about aspell-autobuildhash internal work. Will also enable aspell affix validation. –dry-run Show what would be done, but do nothing real. –force Rebuild the hash file for all dicts providing a compat file skipping the test. –triggered Tell the…
arpwatch_selinux – Security Enhanced Linux Policy for the arpwatch processes Description Security-Enhanced Linux secures the arpwatch processes via flexible mandatory access control. The arpwatch processes execute with the arpwatch_t SELinux type. You can check if you have these processes running by executing the ps command with the -Z qualifier. For example: ps -eZ | grep…
arpwatch – keep track of ethernet/ip address pairings Synopsis arpwatch [ -dNp ] [ -f datafile ] [ -i interface ] [ -n net[/width ]] [ -r file ] [ -u username ] [ -e username ] [ -s username ] Description Arpwatch keeps track for ethernet/ip address pairings. It syslogs activity and reports…
arptables – ARP table administration Synopsis arptables [-t table] –[AD] chain rule-specification [options] arptables [-t table] –[RI] chain rulenum rule-specification [options] arptables [-t table] -D chain rulenum [options] arptables [-t table] –[LFZ][chain][options] arptables [-t table] –[NX] chain arptables [-t table] -E old-chain-name new-chain-name arptables [-t table] -P chain target [options] Description arptables is a user…
arptables-save — dump arptables rules to stdout Synopsis arptables-save Description arptables-save is used to dump the contents of an ARP Table in easily parseable format to STDOUT. Use I/O-redirection provided by your shell to write to a file. Bugs None known as of arptables-0.0.4 release Author Jesper Dangaard Brouer <brouer [at] redhat.com> See Also arptables-restore(8),…