The Linux Manuals (man pages) document is an important part of Linux documents. Linux Manuals are organized as several sections. Each section has a group of commands for a specific area in Linux usage, administration or development.
jfs_mkfs – create a JFS formatted partition Synopsis jfs_mkfs [options] device [ blocks ] Description jfs_mkfs is used to create (format) a JFS partition. jfs_mkfs must be run as root. device is the special file name corresponding to the actual device (e.g. /dev/hdb1) on which a JFS file system and/or JFS journal will be created….
jfs_logdump – dump a JFS formatted device’s journal log Synopsis jfs_logdump [ -a ] device Description jfs_logdump dumps the contents of the journal log from the specified JFS formatted device into output file ./jfslog.dmp. device is the special file name corresponding to the actual device from which the journal log will be dumped (e.g. /dev/hdb1…
jfs_fscklog – extract a JFS fsck service log into a file and/or format and display the extracted file Synopsis jfs_fscklog [ -d ] [ -e device ] [ -f output.file ] [ -p ] [ -V ] Description jfs_fscklog with option -e device extracts the contents of either the most recent or immediately prior (specified…
jfs_fsck – initiate replay of the JFS transaction log, and check and repair a JFS formatted device Synopsis jfs_fsck [ -afnpvV ] [ -j journal_device ] [ –omit_journal_replay ] [ –replay_journal_only ] device Description jfs_fsck is used to replay the JFS transaction log, check a JFS formatted device for errors, and fix any errors found….
jfs_debugfs – shell-type JFS file system editor Synopsis jfs_debugfs device Description jfs_debugfs is a program which can be used to perform various low-level actions on a JFS formatted device. device is the special file name corresponding to the actual device to be edited (e.g. /dev/hdb1). jfs_debugfs must be run as root. Commands a[lter] <block> <offset>…
jabberd_selinux – Security Enhanced Linux Policy for the jabberd processes Description Security-Enhanced Linux secures the jabberd processes via flexible mandatory access control. The jabberd processes execute with the jabberd_t SELinux type. You can check if you have these processes running by executing the ps command with the -Z qualifier. For example: ps -eZ | grep…
jabberd_router_selinux – Security Enhanced Linux Policy for the jabberd_router processes Description Security-Enhanced Linux secures the jabberd_router processes via flexible mandatory access control. The jabberd_router processes execute with the jabberd_router_t SELinux type. You can check if you have these processes running by executing the ps command with the -Z qualifier. For example: ps -eZ | grep…
jabberd – jabberd startup script Synopsis jabberd [-h] [-c config] [-D] Description jabberd is a script that runs the various components that make up the jabberd "server". Options -h Show summary of options. -c Alternate configuration file to use. The compiled-in default is /etc/jabberd/jabberd.cfg -D Print debugging output. You should configure jabberd with the –enable-debug…
ixpdimm-monitor – Daemon to monitor Intel(R) DIMM management events. Used by ixpdimm-cli. Synopsis ixpdimm-monitor [-d] Description Daemon to monitor Intel(R) DIMM management events. These events can be viewed using ixpdimm-cli. Option -d Starts ixpdimm-monitor as a background daemon. Exit Codes 0 The operation succeeded. 1 An error occurred. Files /var/lib/ixpdimm_sw/apss.dat /var/run/ixpdimm-monitor.pid See Also ixpdimm-cli (8)…
ixpdimm-cli – CLI to manage Intel(R) DIMMs Synopsis ixpdimm-cli <verb> [<options>] [<targets>] [<properties>] verb A command has a single verb which represents the action to be taken. Verb choices are create, delete, dump, help, load, set, show, start, and version. Use <verb> -help to see available commands for a specific verb. options Following the verb…
iwspy – Get wireless statistics from specific nodes Synopsis iwspy [interface] iwspy interface [+] DNSNAME | IPADDR | HWADDR […] iwspy interface off iwspy interface setthr low high iwspy interface getthr Description Iwspy is used to set a list of addresses to monitor in a wireless network interface and to read back quality of link…
iwpriv – configure optionals (private) parameters of a wireless network interface Synopsis iwpriv [interface] iwpriv interface private-command [private-parameters] iwpriv interface private-command [I] [private-parameters] iwpriv interface –all Description Iwpriv is the companion tool to iwconfig(8). Iwpriv deals with parameters and setting specific to each driver (as opposed to iwconfig which deals with generic ones). Without any…
iwlist – Get more detailed wireless information from a wireless interface Synopsis iwlist [interface] scanning iwlist [interface] frequency iwlist [interface] rate iwlist [interface] keys iwlist [interface] power iwlist [interface] txpower iwlist [interface] retry iwlist [interface] event iwlist [interface] auth iwlist [interface] wpakeys iwlist [interface] genie iwlist [interface] modulation iwlist –help iwlist –version Description Iwlist is…
iwhd_selinux – Security Enhanced Linux Policy for the iwhd processes Description Security-Enhanced Linux secures the iwhd processes via flexible mandatory access control. The iwhd processes execute with the iwhd_t SELinux type. You can check if you have these processes running by executing the ps command with the -Z qualifier. For example: ps -eZ | grep…
iwgetid – Report ESSID, NWID or AP/Cell Address of wireless network Synopsis iwgetid [interface] [–raw] [–scheme] [–ap] [–freq] [–mode] [–protocol] [–channel] Description iwgetid is used to find out the NWID, ESSID or AP/Cell Address of the wireless network that is currently used. The information reported is the same as the one shown by iwconfig, but…
iwevent – Display Wireless Events generated by drivers and setting changes Synopsis iwevent Description iwevent displays Wireless Events received through the RTNetlink socket. Each line displays the specific Wireless Event which describes what has happened on the specified wireless interface. This command doesn’t take any arguments. Display There are two classes of Wireless Events. The…
ipmiutil_wdt- display and set WatchDog Timer parameters Synopsis ipmiutil wdt [-acdelrtx -N node -P/-R pswd -U user -EFJTVY] Description ipmiutil wdt is a program that uses IPMI commands to display and set WatchDog Timer parameters. This utility can use either any available IPMI driver, or direct user-space IOs, or the IPMI LAN interface if -N….
iwconfig – configure a wireless network interface Synopsis iwconfig [interface] iwconfig interface [essid X] [nwid N] [mode M] [freq F] [channel C][sens S ][ap A ][nick NN ] [rate R] [rts RT] [frag FT] [txpower T] [enc E] [key K] [power P] [retry R] [modu M] [commit] iwconfig –help iwconfig –version Description Iwconfig is similar…
iw – show / manipulate wireless devices and their configuration Synopsis iw [ OPTIONS ] { help [ command ] | OBJECT COMMAND } OBJECT := { dev | phy | reg } OPTIONS := { –version | –debug } Options –version print version information and exit. –debug enable netlink message debugging. Iw – Command…
ivtscd – driver for the IVT Solar Controller Device Note This man page only documents the hardware-specific features of the ivtscd driver. For information about the core driver, see nutupsdrv(8). Description This driver allows to access the IVT SCD-series devices. Extra Arguments This driver does not support any extra argument. Author Arjen de Korte <adkorte-guest…