renice (1p) - Linux Man Pages
renice: set nice values of running processes
PROLOGThis manual page is part of the POSIX Programmer's Manual. The Linux implementation of this interface may differ (consult the corresponding Linux manual page for details of Linux behavior), or the interface may not be implemented on Linux.
renice - set nice values of running processes
The renice utility shall request that the nice values (see the Base Definitions volume of IEEE Std 1003.1-2001, Section 3.239, Nice Value) of one or more running processes be changed. By default, the applicable processes are specified by their process IDs. When a process group is specified (see -g), the request shall apply to all processes in the process group.
The nice value shall be bounded in an implementation-defined manner. If the requested increment would raise or lower the nice value of the executed utility beyond implementation-defined limits, then the limit whose value was exceeded shall be used.
When a user is reniced, the request applies to all processes whose saved set-user-ID matches the user ID corresponding to the user.
Regardless of which options are supplied or any other factor, renice shall not alter the nice values of any process unless the user requesting such a change has appropriate privileges to do so for the specified process. If the user lacks appropriate privileges to perform the requested action, the utility shall return an error status.
The saved set-user-ID of the user's process shall be checked instead of its effective user ID when renice attempts to determine the user ID of the process in order to determine whether the user has appropriate privileges.
The renice utility shall conform to the Base Definitions volume of IEEE Std 1003.1-2001, Section 12.2, Utility Syntax Guidelines.
The following options shall be supported:
- Interpret all operands as unsigned decimal integer process group IDs.
- Specify how the nice value of the specified process or processes is to be adjusted. The increment option-argument is a positive or negative decimal integer that shall be used to modify the nice value of the specified process or processes.
Positive increment values shall cause a lower nice value. Negative increment values may require appropriate privileges and shall cause a higher nice value.
- Interpret all operands as unsigned decimal integer process IDs. The -p option is the default if no options are specified.
Interpret all operands as users. If a user exists with a user name
equal to the operand, then the user ID of that user is used
in further processing. Otherwise, if the operand represents an unsigned
decimal integer, it shall be used as the numeric user ID of
The following operands shall be supported:
A process ID, process group ID, or user name/user ID, depending on
the option selected.
The following environment variables shall affect the execution of renice:
- Provide a default value for the internationalization variables that are unset or null. (See the Base Definitions volume of IEEE Std 1003.1-2001, Section 8.2, Internationalization Variables for the precedence of internationalization variables used to determine the values of locale categories.)
- If set to a non-empty string value, override the values of all the other internationalization variables.
- Determine the locale for the interpretation of sequences of bytes of text data as characters (for example, single-byte as opposed to multi-byte characters in arguments).
- Determine the locale that should be used to affect the format and contents of diagnostic messages written to standard error.
Determine the location of message catalogs for the processing of LC_MESSAGES
The following exit values shall be returned:
- Successful completion.
- An error occurred.
CONSEQUENCES OF ERRORS
Adjust the nice value so that process IDs 987 and 32 would have a
lower nice value:
renice -n 5 -p 987 32
Adjust the nice value so that group IDs 324 and 76 would have a higher
nice value, if the user has the appropriate privileges to
renice -n -4 -g 324 76
Adjust the nice value so that numeric user ID 8 and user sas
would have a lower nice value:
renice -n 4 -u 8 sas
Useful nice value increments on historical systems include 19 or 20 (the affected processes run only when nothing else in the system attempts to run) and any negative number (to make processes run faster).
The gid, pid, and user specifications do not fit either the definition of operand or option-argument. However, for clarity, they have been included in the OPTIONS section, rather than the OPERANDS section.
The definition of nice value is not intended to suggest that all processes in a system have priorities that are comparable. Scheduling policy extensions such as the realtime priorities in the System Interfaces volume of IEEE Std 1003.1-2001 make the notion of a single underlying priority for all scheduling policies problematic. Some implementations may implement the nice-related features to affect all processes on the system, others to affect just the general time-sharing activities implied by this volume of IEEE Std 1003.1-2001, and others may have no effect at all. Because of the use of "implementation-defined" in nice and renice, a wide range of implementation strategies are possible.
Originally, this utility was written in the historical manner, using the term "nice value". This was always a point of concern with users because it was never intuitively obvious what this meant. With a newer version of renice, which used the term "system scheduling priority", it was hoped that novice users could better understand what this utility was meant to do. Also, it would be easier to document what the utility was meant to do. Unfortunately, the addition of the POSIX realtime scheduling capabilities introduced the concepts of process and thread scheduling priorities that were totally unaffected by the nice/ renice utilities or the nice()/ setpriority() functions. Continuing to use the term "system scheduling priority'' would have incorrectly suggested that these utilities and functions were indeed affecting these realtime priorities. It was decided to revert to the historical term "nice value" to reference this unrelated process attribute.
Although this utility has use by system administrators (and in fact appears in the system administration portion of the BSD documentation), the standard developers considered that it was very useful for individual end users to control their own processes.
COPYRIGHTPortions of this text are reprinted and reproduced in electronic form from IEEE Std 1003.1, 2003 Edition, Standard for Information Technology -- Portable Operating System Interface (POSIX), The Open Group Base Specifications Issue 6, Copyright (C) 2001-2003 by the Institute of Electrical and Electronics Engineers, Inc and The Open Group. In the event of any discrepancy between this version and the original IEEE and The Open Group Standard, the original IEEE and The Open Group Standard is the referee document. The original Standard can be obtained online at http://www.opengroup.org/unix/online.html .