sensors.conf (5) - Linux Manuals
sensors.conf: libsensors configuration file
NAME
sensors.conf - libsensors configuration file
DESCRIPTION
sensors.conf describes how libsensors, and so all programs using it, should translate the raw readings from the kernel modules to real-world values.SEMANTICS
On a given system, there may be one or more hardware monitoring chips. Each chip may have several features. For example, the LM78 monitors 7 voltage inputs, 3 fans and one temperature. Feature names are standardized. Typical feature names are in0, in1, in2... for voltage inputs, fan1, fan2, fan3... for fans and temp1, temp2, temp3... for temperature inputs.
Each feature may in turn have one or more sub-features, each representing an attribute of the feature: input value, low limit, high limit, alarm, etc. Sub-feature names are standardized as well. For example, the first voltage input (in0) would typically have sub-features in0_input (measured value), in0_min (low limit), in0_max (high limit) and in0_alarm (alarm flag). Which sub-features are actually present depend on the exact chip type.
The sensors.conf configuration file will let you configure each chip, feature and sub-feature in a way that makes sense for your system.
The rest of this section describes the meaning of each configuration statement.
CHIP STATEMENT
A chip statement selects for which chips all following compute, label, ignore and set statements are meant. A chip selection remains valid until the next chip statement. Example:
- chip "lm78-*" "lm79-*"
If a chip matches at least one of the chip descriptions, the following configuration lines are examined for it, otherwise they are ignored.
A chip description is built from several elements, separated by dashes. The first element is the chip type, the second element is the name of the bus, and the third element is the hexadecimal address of the chip. Such chip descriptions are printed by sensors(1) as the first line for every chip.
The name of the bus is either isa, pci, virtual, spi-*, i2c-N or mdio with N being a bus number as bound with a bus statement. This list isn't necessarily exhaustive as support for other bus types may be added in the future.
You may substitute the wildcard operator * for every element. Note however that it wouldn't make any sense to specify the address without the bus type, so the address part is plain omitted when the bus type isn't specified. Here is how you would express the following matches:
LM78 chip at address 0x2d on I2C bus 1 | lm78-i2c-1-2d |
LM78 chip at address 0x2d on any I2C bus | lm78-i2c-*-2d |
LM78 chip at address 0x290 on the ISA bus | lm78-isa-0290 |
Any LM78 chip on I2C bus 1 | lm78-i2c-1-* |
Any LM78 on any I2C bus | lm78-i2c-*-* |
Any LM78 chip on the ISA bus | lm78-isa-* |
Any LM78 chip | lm78-* |
Any chip at address 0x2d on I2C bus 1 | *-i2c-1-2d |
Any chip at address 0x290 on the ISA bus | *-isa-0290 |
If several chip statements match a specific chip, they are all considered.
LABEL STATEMENT
A label statement describes how a feature should be called. Features without a label statement are just called by their feature name. Applications can use this to label the readings they present. Example:
- label in3 "+5V"
The first argument is the feature name. The second argument is the feature description.
Note that you must use the raw feature name, which is not necessarily the one displayed by "sensors" by default. Use "sensors -u" to see the raw feature names. Same applies to all other statement types below.
IGNORE STATEMENT
An ignore statement is a hint that a specific feature should be ignored - probably because it returns bogus values (for example, because a fan or temperature sensor is not connected). Example:
- ignore fan1
The only argument is the feature name. Please note that this does not disable anything in the actual sensor chip; it simply hides the feature in question from libsensors users.
COMPUTE STATEMENT
A compute statement describes how a feature's raw value should be translated to a real-world value, and how a real-world value should be translated back to a raw value again. This is most useful for voltage sensors, because in general sensor chips have a limited range and voltages outside this range must be divided (using resistors) before they can be monitored. Example:
- compute in3 ((6.8/10)+1)*@, @/((6.8/10)+1)
The example above expresses the fact that the voltage input is divided using two resistors of values 6.8 Ohm and 10 Ohm, respectively. See the VOLTAGE COMPUTATION DETAILS section below for details.
The first argument is the feature name. The second argument is an expression which specifies how a raw value must be translated to a real-world value; `@' stands here for the raw value. This is the formula which will be applied when reading values from the chip. The third argument is an expression that specifies how a real-world value should be translated back to a raw value; `@' stands here for the real-world value. This is the formula which will be applied when writing values to the chip. The two formulas are obviously related, and are separated by a comma.
A compute statement applies to all sub-features of the target feature for which it makes sense. For example, the above example would affect sub-features in3_min and in3_max (which are voltage values) but not in3_alarm (which is a boolean flag.)
The following operators are supported in compute statements:
- + - * / ( ) ^ `
You may use the name of sub-features in these expressions; current readings are substituted. You should be careful though to avoid circular references.
If at any moment a translation between a raw and a real-world value is called for, but no compute statement applies, a one-on-one translation is used instead.
SET STATEMENT
A set statement is used to write a sub-feature value to the chip. Of course not all sub-feature values can be set that way, in particular input values and alarm flags can not. Valid sub-features are usually min/max limits. Example:
- set in3_min 5 * 0.95
- set in3_max 5 * 1.05
The example above basically configures the chip to allow a 5% deviance for the +5V power input.
The first argument is the feature name. The second argument is an expression which determines the written value. If there is an applying compute statement, this value is fed to its third argument to translate it to a raw value.
You may use the name of sub-features in these expressions; current readings are substituted. You should be careful though to avoid circular references.
Please note that set statements are only executed by sensors(1) when you use the -s option. Typical graphical sensors applications do not care about these statements at all.
BUS STATEMENT
A bus statement binds the description of an I2C or SMBus adapter to a bus number. This makes it possible to refer to an adapter in the configuration file, independent of the actual correspondence of bus numbers and actual adapters (which may change from moment to moment). Example:
- bus "i2c-0" "SMBus PIIX4 adapter at e800"
The first argument is the bus number. It is the literal text i2c-, followed by a number. As there is a dash in this argument, it must always be quoted.
The second argument is the adapter name, it must match exactly the adapter name as it appears in /sys/class/i2c-adapter/i2c-*/name. It should always be quoted as well as it will most certainly contain spaces or dashes.
The bus statements may be scattered randomly throughout the configuration file; there is no need to place the bus line before the place where its binding is referred to. Still, as a matter of good style, we suggest you place all bus statements together at the top of your configuration file.
Running sensors --bus-list will generate these lines for you.
In the case where multiple configuration files are used, the scope of each bus statement is the configuration file it was defined in. This makes it possible to have bus statements in all configuration files which will not unexpectedly interfere with each other.
STATEMENT ORDER
Statements can go in any order, however it is recommended to put `set fanX_div' statements before `set fanX_min' statements, in case a driver doesn't preserve the fanX_min setting when the fanX_div value is changed. Even if the driver does, it's still better to put the statements in this order to avoid accuracy loss.
VOLTAGE COMPUTATION DETAILS
Most voltage sensors in sensor chips have a range of 0 to 4.08 V. This is generally sufficient for the +3.3V and CPU supply voltages, so the sensor chip reading is the actual voltage.
Other supply voltages must be scaled with an external resistor network. The driver reports the value at the chip's pin (0 - 4.08 V), and the userspace application must convert this raw value to an actual voltage. The compute statements provide this facility.
Unfortunately the resistor values vary among motherboard types. Therefore you have to figure out the correct resistor values for your own motherboard.
For positive voltages (typically +5V and +12V), two resistors are used,
with the following formula:
where:
This leads to the following compute formula:
Real-world formula for +5V and +12V would look like:
For negative voltages (typically -5V and -12V), two resistors are used
as well, but different boards use different strategies to bring the
voltage value into the 0 - 4.08 V range. Some use an inverting
amplifier, others use a positive reference voltage. This leads to
different computation formulas. Note that most users won't have to care
because most modern motherboards make little use of -12V and no use of
-5V so they do not bother monitoring these voltage inputs.
Real-world examples for the inverting amplifier case:
Real-world examples for the positive voltage reference case:
Many recent monitoring chips have a 0 - 2.04 V range, so scaling resistors
are even more needed, and resistor values are different.
There are also a few chips out there which have internal scaling
resistors, meaning that their value is known and doesn't change from
one motherboard to the next. For these chips, the driver usually
handles the scaling so it is transparent to the user and no
compute
statements are needed.
On top of the usual features, temperatures can have two specific
sub-features: temperature sensor type (tempX_type) and hysteresis
values (tempX_max_hyst, tempX_crit_hyst etc.).
Available thermal sensor types:
For example, to set temp1 to thermistor type, use:
Only certain chips support thermal sensor type change, and even these
usually only support some of the types above. Please refer to the
specific driver documentation to find out which types are supported
by your chip.
In theory, the BIOS should have configured the sensor types correctly,
so you shouldn't have to touch them, but sometimes it isn't the case.
Many monitoring chips do not handle the high and critical temperature
limits as simple limits. Instead, they have two values for each
limit, one which triggers an alarm when the temperature rises and another
one which clears the alarm when the temperature falls. The latter is
typically a few degrees below the former. This mechanism is known as
hysteresis.
The reason for implementing things that way is that high temperature
alarms typically trigger an action to attempt to cool the system down,
either by scaling down the CPU frequency, or by kicking in an extra
fan. This should normally let the temperature fall in a timely manner.
If this was clearing the alarm immediately, then the system would be
back to its original state where the temperature rises and the alarm
would immediately trigger again, causing an undesirable tight fan on,
fan off loop. The hysteresis mechanism ensures that the system is
really cool before the fan stops, so that it will not have to kick in
again immediately.
So, in addition to tempX_max, many chips have a tempX_max_hyst
sub-feature. Likewise, tempX_crit often comes with tempX_crit_hyst.
tempX_emerg_hyst, tempX_min_hyst and tempX_lcrit_hyst exist too but
aren't as common.
Example:
The hysteresis mechanism can be disabled by giving both limits the same
value.
Note that it is strongly recommended to set the hysteresis value after
the limit value it relates to in the configuration file. Implementation
details on the hardware or driver side may cause unexpected results if
the hysteresis value is set first.
Some chips support alarms with beep warnings. When an alarm is triggered
you can be warned by a beeping signal through your computer speaker. On
top of per-feature beep flags, there is usually a master beep control
switch to enable or disable beeping globally. Enable beeping using:
or disable it using:
If more than one statement of the same kind applies at a certain moment,
the last one in the configuration file is used. So usually, you should
put more general
chip
statements at the top, so you can overrule them below.
chip
NAME-LIST
label
NAME NAME
compute
NAME EXPR
,
EXPR
ignore
NAME
set
NAME EXPR
A
NAME
is a string. If it only contains letters, digits and underscores, it does not
have to be quoted; in all other cases, you must use double quotes around it.
Within quotes, you can use the normal escape-codes from C.
A
NAME-LIST
is one or more
NAME
items behind each other, separated by whitespace.
A
EXPR
is of one of the below forms:
NAME
@
EXPR
+
EXPR
EXPR
-
EXPR
EXPR
*
EXPR
EXPR
/
EXPR
-
EXPR
^
EXPR
`
EXPR
(
EXPR
)
A
NUMBER
is a floating-point number. `10', `10.4' and `.4' are examples of valid
floating-point numbers; `10.' or `10E4' are not valid.
/etc/sensors.d
TEMPERATURE CONFIGURATION
THERMAL SENSOR TYPES
1 PII/Celeron Diode 2 3904 transistor 3 thermal diode 4 thermistor 5 AMD AMDSI 6 Intel PECI THERMAL HYSTERESIS MECHANISM
BEEPS
WHICH STATEMENT APPLIES
SYNTAX
Comments are introduced by hash marks. A comment continues to the end of the
line. Empty lines, and lines containing only whitespace or comments are
ignored. Other lines have one of the below forms. There must be whitespace
between each element, but the amount of whitespace is unimportant. A line
may be continued on the next line by ending it with a backslash; this does
not work within a comment,
NAME
or
NUMBER.
FILES
/etc/sensors3.conf
/etc/sensors.conf
AUTHOR
Frodo Looijaard and the lm_sensors group
https://hwmon.wiki.kernel.org/lm_sensors