radmin (8) - Linux Manuals

radmin: FreeRADIUS Administration tool

NAME

radmin - FreeRADIUS Administration tool

SYNOPSIS

radmin [-d config_directory] [-e command] [-E] [-f socket_file] [-h] [-i input_file] [-n name] [-o output_file] [-q]

DESCRIPTION

FreeRADIUS Server administration tool that connects to the control socket of a running server, and gives a command-line interface to it.

At this time, only a few commands are supported. Please type "help" at the command prompt for detailed information about the supported commands.

WARNING

The security protections offered by this command are limited to the permissions on the Unix domain socket, and the server configuration. If someone can connect to the Unix domain socket, they have a substantial amount of control over the server.

OPTIONS

The following command-line options are accepted by the program.
-d config directory
Defaults to /etc/raddb. radmin looks here for the server configuration files to find the "listen" section that defines the control socket filename.
-e command
Run command and exit.
-E
Echo commands as they are being executed.
-f socket_file
Specify the socket filename directly. The radiusd.conf file is not read.
-h
Print usage help information.
-i input_file
Reads input from the specified file. If not specified, stdin is used. This also sets "-q".
-n mname
Read raddb/name.conf instead of raddb/radiusd.conf.
-o output_file
Write output to the specified file. If not specified, stdout is used. This also sets "-q".
-q
Quiet mode.

COMMANDS

The commands implemented by the command-line interface are almost completely controlled by the server. There are a few commands interpreted locally by radmin:
reconnect
Reconnect to the server.
quit
Exit from radmin.
exit
Exit from radmin.

The other commands are implemented by the server. Type "help" at the prompt for more information.

EXAMPLES

debug file /var/log/radius/bob.log
Set debug logs to /var/log/radius/bob.log. There is very little checking of this filename. Rogue administrators may be able use this command to over-write almost any file on the system. If those administrators have write access to "radius.conf", they can do the same thing without radmin, too.
debug condition '(User-Name == bob)'
Enable debugging output for all requests that match the condition. Any "unlang" condition is valid here. The condition is parsed as a string, so it must be enclosed in single or double quotes. Strings enclosed in double-quotes must have back-slashes and the quotation marks escaped inside of the string.

Only one debug condition can be active at a time.

debug condition '((User-Name == bob) || (Packet-Src-IP-Address == 192.0.2.22))'
A more complex condition that enables debugging output for requests containing User-Name "bob", or requests that originate from source IP address 192.0.2.22.
debug condition
Disable debug conditionals.

FULL LIST OF COMMANDS

add <command>
do sub-command of add
add client <command>
Add client configuration commands
add client file <filename>
Add new client definition from <filename>
debug <command>
debugging commands
debug condition [condition]
Enable debugging for requests matching [condition]
debug level <number>
Set debug level to <number>. Higher is more debugging.
debug file [filename]
Send all debugging output to [filename]
del <command>
do sub-command of del
del client <command>
Delete client configuration commands
del client ipaddr <ipaddr>
Delete a dynamically created client
hup [module]
sends a HUP signal to the server, or optionally to one module
inject <command>
commands to inject packets into a running server
inject to <ipaddr> <port>
Inject packets to the destination IP and port.
inject from <ipaddr>
Inject packets as if they came from <ipaddr>
inject file <input-file> <output-file>
Inject packet from input-file>, with results sent to <output-file>
reconnect
reconnect to a running server
terminate
terminates the server, and cause it to exit
set <command>
do sub-command of set
set module <command>
set module commands
set module config <module> variable value
set configuration for <module>
set module status [alive|dead]
set the module to be alive or dead (always return "fail")
set home_server <command>
set home server commands
set home_server state <ipaddr> <port> [alive|dead]
set state for given home server
show <command>
do sub-command of show
show client <command>
do sub-command of client
show client config <ipaddr>
show configuration for given client
show client list
shows list of global clients
show debug <command>
show debug properties
show debug condition
Shows current debugging condition.
show debug level
Shows current debugging level.
show debug file
Shows current debugging file.
show home_server <command>
do sub-command of home_server
show home_server config <ipaddr> <port>
show configuration for given home server
show home_server list
shows list of home servers
show home_server state <ipaddr> <port>
shows state of given home server
show module <command>
do sub-command of module
show module config <module>
show configuration for given module
show module flags <module>
show other module properties
show module list
shows list of loaded modules
show module methods <module>
show sections where <module> may be used
show uptime
shows time at which server started
show version
Prints version of the running server
show xml <reference>
Prints out configuration as XML
stats <command>
do sub-command of stats
stats client [auth/acct] <ipaddr>
show statistics for given client, or for all clients (auth or acct)
stats home_server [<ipaddr>/auth/acct] <port>
show statistics for given home server (ipaddr and port), or for all home servers (auth or acct)
stats detail <filename>
show statistics for the given detail file

AUTHOR

Alan DeKok <aland [at] freeradius.org>

SEE ALSO

unlang(5), radiusd.conf(5), raddb/sites-available/control-socket