xfs_info (8) - Linux Man Pages
xfs_info: expand an XFS filesystem
xfs_growfs, xfs_info - expand an XFS filesystem
SYNOPSISxfs_growfs [ -dilnrx ] [ -D size ] [ -e rtextsize ] [ -L size ] [ -m maxpct ] [ -t mtab ] [ -R size ] mount-point
DESCRIPTIONxfs_growfs expands an existing XFS filesystem (see xfs(5)). The mount-point argument is the pathname of the directory where the filesystem is mounted. The filesystem must be mounted to be grown (see mount(8)). The existing contents of the filesystem are undisturbed, and the added space becomes available for additional file storage.
- -d | -D size
- Specifies that the data section of the filesystem should be grown. If the -D size option is given, the data section is grown to that size, otherwise the data section is grown to the largest size possible with the -d option. The size is expressed in filesystem blocks.
- Allows the real-time extent size to be specified. In mkfs.xfs(8) this is specified with -r extsize=nnnn.
- The new log is an internal log (inside the data section). [NOTE: This option is not implemented]
- -l | -L size
- Specifies that the log section of the filesystem should be grown, shrunk, or moved. If the -L size option is given, the log section is changed to be that size, if possible. The size is expressed in filesystem blocks. The size of an internal log must be smaller than the size of an allocation group (this value is printed at mkfs(8) time). If neither -i nor -x is given with -l, the log continues to be internal or external as it was before. [NOTE: These options are not implemented]
- Specify a new value for the maximum percentage of space in the filesystem that can be allocated as inodes. In mkfs.xfs(8) this is specified with -i maxpct=nn.
- Specifies that no change to the filesystem is to be made. The filesystem geometry is printed, and argument checking is performed, but no growth occurs. See output examples below.
- -r | -R size
- Specifies that the real-time section of the filesystem should be grown. If the -R size option is given, the real-time section is grown to that size, otherwise the real-time section is grown to the largest size possible with the -r option. The size is expressed in filesystem blocks. The filesystem does not need to have contained a real-time section before the xfs_growfs operation.
- Specifies an alternate mount table file (default is /proc/mounts if it exists, else /etc/mtab). This is used when working with filesystems mounted without writing to /etc/mtab file - refer to mount(8) for further details.
- Prints the version number and exits. The mount-point argument is not required with -V.
xfs_growfs is most often used in conjunction with logical volumes (see md(4) and lvm(8) on Linux). However, it can also be used on a regular disk partition, for example if a partition has been enlarged while retaining the same starting block.
PRACTICAL USEFilesystems normally occupy all of the space on the device where they reside. In order to grow a filesystem, it is necessary to provide added space for it to occupy. Therefore there must be at least one spare new disk partition available. Adding the space is often done through the use of a logical volume manager.
Understanding xfs_info output.
Suppose one has the following "xfs_info /dev/sda" output:
meta-data=/dev/sda isize=256 agcount=32, agsize=16777184 blks = sectsz=512 attr=2 data = bsize=4096 blocks=536869888, imaxpct=5 = sunit=32 swidth=128 blks naming =version 2 bsize=4096 log =internal bsize=4096 blocks=32768, version=2 = sectsz=512 sunit=32 blks, lazy-count=1 realtime =none extsz=524288 blocks=0, rtextents=0
Here, the data section of the output indicates "bsize=4096", meaning the data block size for this filesystem is 4096 bytes. This section also shows "sunit=32 swidth=128 blks", which means the stripe unit is 32*4096 bytes = 128 kibibytes and the stripe width is 128*4096 bytes = 512 kibibytes. A single stripe of this filesystem therefore consists of four stripe units (128 blocks / 32 blocks per unit).