fence_ilo3 (8) Linux Manual Page
fence_ilo3 – Fence agent for IPMI fence_ilo3 – Fence agent for HP iLO3 (symlink) fence_ilo4 – Fence agent for HP iLO4 (symlink) fence_imm – Fence agent for IBM Integrated Management Module (symlink) fence_idrac – Fence agent for Dell iDRAC (symlink)
Description
fence_ipmilan is an I/O Fencing agentwhich can be used with machines controlled by IPMI.This agent calls support software ipmitool (http://ipmitool.sf.net/). WARNING! This fence agent might report success before the node is powered off. You should use -m/method onoff if your fence device works correctly with that option.
fence_ilo3 accepts options on the command line as well as from stdin. Fenced sends parameters through stdin when it execs the agent. fence_ilo3 can be run by itself with command line options. This is useful for testing and for turning outlets on or off from scripts.
Vendor URL:
Parameters
- -u, –ipport=[port]
- TCP/UDP port to use for connection with device (Default Value: 623)
- -n, –plug=[ip]
- IP address or hostname of fencing device (together with –port-as-ip)
- -6, –inet6-only
- Forces agent to use IPv6 addresses only
- -a, –ip=[ip]
- IP Address or Hostname
- -S, –password-script=[script]
- Script to retrieve password
- -m, –method=[method]
- Method to fence (onoff|cycle) (Default Value: cycle)
- -4, –inet4-only
- Forces agent to use IPv4 addresses only
- -p, –password=[password]
- Login password or passphrase
- -P, –lanplus
- Use Lanplus to improve security of connection (Default Value: 1)
- -A, –auth=[auth]
- IPMI Lan Auth type.
- -o, –action=[action]
- Fencing Action (Default Value: reboot)
- -C, –cipher=[cipher]
- Ciphersuite to use (same as ipmitool -C parameter)
- -L, –privlvl=[level]
- Privilege level on IPMI device (Default Value: administrator)
- -t [seconds] Timeout (sec) for IPMI operation
- Timeout (sec) for IPMI operation
- -l, –username=[name]
- Login Name
- -v, –verbose
- Verbose mode
- -D, –debug-file=[debugfile]
- Write debug information to given file
- -V, –version
- Display version information and exit
- -h, –help
- Display help and exit
- –power-wait=[seconds]
- Wait X seconds after issuing ON/OFF (Default Value: 4)
- –login-timeout=[seconds]
- Wait X seconds for cmd prompt after login (Default Value: 5)
- –delay=[seconds]
- Wait X seconds before fencing is started (Default Value: 0)
- –power-timeout=[seconds]
- Test X seconds for status change after ON/OFF (Default Value: 20)
- –ipmitool-path=[path]
- Path to ipmitool binary (Default Value: /usr/bin/ipmitool)
- –shell-timeout=[seconds]
- Wait X seconds for cmd prompt after issuing command (Default Value: 3)
- –port-as-ip
- Make "port/plug" to be an alias to IP address
- –retry-on=[attempts]
- Count of attempts to retry power on (Default Value: 1)
- –use-sudo
- Use sudo (without password) when calling 3rd party sotfware.
Actions
- on
- Power on machine.
- off
- Power off machine.
- reboot
- Reboot machine.
- status
- This returns the status of the plug/virtual machine.
- list
- List available plugs with aliases/virtual machines if there is support for more then one device. Returns N/A otherwise.
- list-status
- List available plugs with aliases/virtual machines and their power state if it can be obtained without additional commands.
- monitor
- Check the health of fence device
- metadata
- Display the XML metadata describing this resource.
- diag
- Pulse a diagnostic interrupt to the processor(s).
Stdin Parameters
- ipport
- TCP/UDP port to use for connection with device (Default Value: 623)
- port
- IP address or hostname of fencing device (together with –port-as-ip)
- inet6_only
- Forces agent to use IPv6 addresses only
- ipaddr
- IP Address or Hostname
- passwd_script
- Script to retrieve password
- method
- Method to fence (onoff|cycle) (Default Value: cycle)
- inet4_only
- Forces agent to use IPv4 addresses only
- passwd
- Login password or passphrase
- lanplus
- Use Lanplus to improve security of connection (Default Value: 1)
- auth
- IPMI Lan Auth type.
- action
- Fencing Action (Default Value: reboot)
- cipher
- Ciphersuite to use (same as ipmitool -C parameter)
- privlvl
- Privilege level on IPMI device (Default Value: administrator)
- timeout
- Timeout (sec) for IPMI operation
- login
- Login Name
- verbose
- Verbose mode
- debug
- Write debug information to given file
- version
- Display version information and exit
- help
- Display help and exit
- power_wait
- Wait X seconds after issuing ON/OFF (Default Value: 4)
- login_timeout
- Wait X seconds for cmd prompt after login (Default Value: 5)
- delay
- Wait X seconds before fencing is started (Default Value: 0)
- power_timeout
- Test X seconds for status change after ON/OFF (Default Value: 20)
- ipmitool_path
- Path to ipmitool binary (Default Value: /usr/bin/ipmitool)
- shell_timeout
- Wait X seconds for cmd prompt after issuing command (Default Value: 3)
- port_as_ip
- Make "port/plug" to be an alias to IP address
- retry_on
- Count of attempts to retry power on (Default Value: 1)
- sudo
- Use sudo (without password) when calling 3rd party sotfware.